Serpent Viper 990E 4wd 1/8 EP (SER904006)
The Serpent Viper 990E is the successor of the successful 988E/989E.
We have spent a lot of testing and research to improve the former electric powered 1-8 platforms.
We put a lot of emphasis on the flex characteristic since that showed very promising results.
On top of that we improved weight, weight distribution and ease of maintenance.
A lot of the development went into the transmission.
The goal was to have a bullet-proved, yet very free transmission
| 11-14-22 | Picture file Viper 990e | 5 MB | Download |
| 11-14-22 | Ref guide Viper 990e V1 | 57 KB | Download |
| 11-14-22 | Manual Viper 990e V1 | 11 MB | Download |
New key features
The ultra-narrow chassis is milled down to allow the lowest possible mounting of the batteries plate as well as improving the overall flex characteristics.
The central part of the chassis features 3 NACA ducts for the cooling of the speedo as well as the motor
The motor has been put as low as possible by machining the chassis underneath it. This improves the centre of gravity as well as the cooling from the bottom.
The rear of the chassis has a slot. This has become a very important feature of the Nitro 990. It has to do with adjustable flex.
It also carries 2 steel countersunk screws that act as a counterpart of the down-stop screws. This helps to keep the down-stop more accurate and consistent
The overall flex is controlled by the “backbone”, a very popular feature of the 988E.
The front of the car can be adjusted to more flex by removing the 2 front screws or even the one on top of the servosaver.
The rear of the car is also adjustable regarding the flex. The regular rear end features the proven, one-piece rear plate
As an option it is also possible to use a softer rear end using a optional 2-piece rear plate
The receiver and the steering servo are mounted on a small “radio plate” which can be easily removed for easy access.
The aluminium servo mounts are eccentric and can be mounted in 2 ways to adjust them to the brand of servos.
The rear end is completely new. It features a new design to allow an re-active toe-change as well as avoid any binding at all!
By changing the position of the link the amount of toe-gain under compression can be adjusted. The position shown is the “neutral” position.
Since the upper link is replaced by a suspension arm, we also changed the upper pivot on the upright. It is now super easy to adjust the correct camber.
The height of the pivot ball is adjustable by changing the aluminium insert. There are 3 positions
The upright carries an aluminium insert where the ball bearings of the wheel axle sit. In that way we can achieve the perfect roundness even under load to achieve the least friction of the transmission possible.
In this way it is also really easy to remove the wheel axle/driveshaft for maintenance
The front steering-block features a similar construction.
The aluminium insert gives the same advantages as in the rear with improved drivetrain effectivity and improved ease of maintenance
The front upper suspension bracket now has an improved design takes provides a better placement to avoid camber or caster irregularities by using bushings.
The new transmission is super strong, yet very light and super easy to maintain.
The pulley of the mid-belt is sitting on a steel adapter that is secured by a steel pin.
The spurgear adapter is fixed with 2 of these pins. Changing the spurgear is super easy, just remove 3 screws
General features
7075 T6 Aluminium 5mm chassis plate
The 5mm aluminium chassis has perfect symmetrical shape for even flex and weight distribution. The ultra-narrow chassis is very light, while it still remains strong in critical places.
The wire type front anti-roll bar is ball raced. It is easy to change and adjust due to the open front end design. The standard wire is 2.5mm and 2 optional thicknesses are available. The pivot ball link system directs the suspension movement to the bar and allows easy tweak adjustment.
The long durable front lower wishbones are the open-style arms similar to the 977. An aluminium shock mount plate is screwed onto the lower wishbone. This allows the shock attachment point to be placed further outwards improving shock motion. The front lower arms are mounted to the front brackets with nylon holders. The kit includes 2 versions: in and out. This system also enables quick and easy front drive shaft maintenance.
Of course the 988 closed arms are usable as well
The left and right interchangeable upper arms are mounted with 3 position nylon suspension pin inserts. The 3 position inserts allow camber-change adjustments and are held in place by the anodized aluminium top brackets. Below the top brackets, spacers can be used to change their angle or height. Caster is adjusted with clips on the upper pivot pins. The same clips are also used on the lower pivot pins to change wheelbase.
The black anodized aluminium front axle has Japan made one-way bearings. Spring steel drive cups connect to the long and thin spring-steel drive shafts with CVD system. The ball raced spring steel wheel axles have aluminium quick-change levers. The open front end design allows for very fast and easy removal of the front axle and driveline parts.
The central mounted seervosaver allows easy and fast Ackermann adjustment. The servosaver features a top mounted insert which can be used in 3 positions. Another 2 Ackermann positions are available on the steering blocks.
The rear end construction with aluminium brackets is a very open design, which allows for easy of maintenance and cleaning. Dis-assembly requires the removal of only a few screws. Replacing a belt if needed, is a simple task. The eccentric bearing holders on the rear shaft allow adjustment of belt tension. The whole rear end can be removed as one unit from the chassis by removal of only a few screws.
The wire type rear anti-roll bar is ball raced. It is mounted in the rear bearing blocks and is easy to change and adjust. The standard wire is 2.5mm and 2 optional thicknesses are available. The pivot ball link system directs the suspension movement to the bar and allows easy tweak adjustment.
The narrow solid rear axle in Serpent spring steel has a lightweight 9mm wide 48T pulley. Spring steel, CVD type, drive shafts connect the rear shaft to spring steel wheel-axles with aluminium quick-change levers. A very durable and long lasting drivetrain.
The rear floating body mount which is mounted on the up-rights with 2 arms is centred by a carbon-fibre and steel guider. The mount has 4 positions on each side to choose from, depending on body shell used and traction available. The threaded holes on the end of the body mount give the option to add further body-supports.
Optionals
A large selection of optional parts is available to even further improve performance, speed, weight and looks.
카테고리 전체보기
